کارایی جاذب مغناطیسی دانه‌ای‌شکل بر پایه زئولیت طبیعی-پلیمر کیتوسان در حذف آرسنیک از آب‌های آلوده

نوع مقاله : پژوهشی

نویسندگان

تبریز، دانشگاه تبریز، دانشکده مهندسی شیمی و نفت، گروه مهندسی شیمی، صندوق پستی 16471-51666

چکیده

فرضیه: از میان آلاینده‌های مختلف موجود در آب طبیعی، آرسنیک به‌دلیل سمیت زیاد، از اهمیت بیشتری برخوردار است. جذب سطحی یکی از کاراترین روش‌ها برای حذف این آلودگی‌ از جریان‌های آب آلوده به آن است. از جمله جاذب‌های آرسنیک می‌توان به نانوکامپوزیت‌های زئولیتی اشاره کرد. جاذب‌های پودری به‌دلیل ایجاد مشکلاتی از قبیل گرفتگی صافی‌ها، افت فشار زیاد پمپ و نیز مشکل جداسازی از آب در سامانه‌های صنعتی کارایی چندانی ندارند.
روش‌ها: برای حل مشکل نام‌برده، پودرهای نانوکامپوزیت زئولیتی با روش ژل‌سازی به‌کمک پلیمر 
کیتوسان و با سه نوع محلول‌ اتصال‌دهنده عرضی شامل سدیم هیدروکسید، سدیم تری‌پلی‌فسفات و سدیم هیدروکسید + سدیم تری‌پلی‌فسفات دانه‌ای‌شکل شدند. اثر عوامل مختلفی از قبیل نوع و نسبت اولیه مواد در شکل‌گیری دانه‌های تهیه‌شده بررسی شد.
یافته‌ها: نتایج نشان داد، دانه‌ها در محلول اتصال‌دهنده عرضی سدیم هیدروکسید + سدیم تری‌پلی‌فسفات و نسبت اولیه بهینه 1 به 3 از کیتوسان به نانوکامپوزیت شکل ظاهری مناسب‌تر و استحکام بهتر و نیز عملکرد بهتری در جذب آرسنیک دارند. به‌منظور تأیید و توجیه نتایج فوق از آزمون‌های SEM، BET و AAS استفاده شد. پارامترهای عملیاتی مختلف از قبیل مقدار غلظت اولیه آرسنیک و دُز جاذب در بازده جذب این دانه‌ها بررسی و مقدار بهینه دُز جاذب 1g/L، با بازده 92.9 تعیین شد. در ادامه‌، برای دستیابی به اطلاعات بیشتر درباره نحوه جذب و تعیین حداکثر ظرفیت جاذب، هم‌دما‌های Langmuir و Freundlich برای جاذب‌های دانه‌ای بررسی شدند. بیشترین ظرفیت جذب 7450.7mg/g به‌دست آمد و نتایج نشادن داد، هم‌دمای Freundlich هم‌خوانی بهتری با داده‌های به‌دست‌آمده دارد. 

کلیدواژه‌ها

عنوان مقاله [English]

Efficiency of Magnetic Granular Adsorbent Based on Natural Zeolite/Chitosan in Removing Arsenic from Polluted Water

نویسندگان [English]

  • Maryam tahmasebpoor
  • Leila Sanaei
  • maryam noori
Faculty of Chemical and Petroleum Engineering, University of Tabriz, P.O. Box 51666-16471, Tabriz, Iran
چکیده [English]

Hypothesis: Among the various pollutants found in natural water, the heavy metal arsenic is more important due to its high toxicity. One of the most efficient methods to remove this pollution from water streams is the surface adsorption method. Zeolite nanocomposites can be considered powerful among arsenic adsorbers. Powder adsorbents are not very effective in industrial systems due to the problems such as clogging of filters, high pressure drop and also the problem of separation from water.
Methods: To solve this problem, zeolite nanocomposite powder was transformed into beads using the chitosan gel method in three different types of cross-linking solutions including sodium hydroxide, sodium tripolyphosphate and joint sodium hydroxide/sodium tripolyphosphate. The effect of various parameters such as the type and initial ratio of the materials on the formation of beads was investigated.
Findings: The results showed that the beads formed in the sodium hydroxide+sodium tripolyphosphate cross-linking solution and the optimal initial ratio of 1:3 from chitosan to the nanocomposite have a more suitable appearance and strength and better performance in arsenic absorption. In order to confirm and justify the mentioned Findings, SEM, BET and AAS analyses were performed. Operational parameters of initial arsenic concentration and adsorbent dose which are effective on the beads’ adsorption efficiency were investigated and the optimal amount of adsorbent dose was determined as 1 g/L with an efficiency of 92.9%. In order to obtain more information about the method of adsorption and determining the maximum capacity of adsorbents, Langmuir and Freundlich isotherms for granular adsorbents were investigated. The highest adsorption capacity of 7450.7 mg/g was obtained and Freundlich isotherm was in better agreement with the results.

کلیدواژه‌ها [English]

  • Adsorbent
  • Chitosan polymer
  • Natural zeolite
  • arsenic
  • Bead

مراجع

  1. Gautam R.K., Sharma S.K., Mahiya S., and Chattopadhyaya M.C., Contamination of Heavy Metals in Aquatic Media: Transport, Toxicity and Technologies for Remediation, Heavy Metals in Water: Presence, Removal and Safety, 1, 1-24, 2014.
  2. Council N., Chemistry and Analysis of Arsenic Species in Water, Food, Urine, Blood, Hair, and Nails, Arsenic in Drinking Water, National Academies, 1999.
  3. Labik L.K., Synthesis of Zeolites and Their Applications to Removal of Arsenic and Ammonia-Nitrogen from Samples of Contaminated Water, MSc Thesis, College of Science, Kwame Nkrumah University of Science and Technology, Kumasi, Ghana, 2012 .
  4. Kong S., Wang Y., Hu Q., and Olusegun A.K., Magnetic Nanoscale Fe-Mn Binary Oxides Loaded Zeolite for Arsenic Removal from Synthetic Groundwater, Colloids Surf. A: Physicochem. Eng. Asp., 457, 220-227, 2014.
  5. Smith A.H. and Steinmaus C.M., Health Effects of Arsenic and Chromium in Drinking Water: Recent Human Findings, Rev. Public Health, 30, 107, 2009.
  6. Sharma P.K., Kumar R., Singh R.K., Sharma P., Ghosh A., Review on Arsenic Removal Using Biochar-Based Materials, Sustain. Dev., 17, 100740-100751, 2022,
  7. Jeon C.-S., Baek K., Park J.-K., Oh Y.-K., and Lee S.-D., Adsorption Characteristics of As(V) on Iron-Coated Zeolite, Hazard. Mater., 163, 804-808, 2009.
  8. Shokri E., Yegani R., and Kazemian N., Fabrication and Evaluation of Polysulfone-Montmorillonite Composite Matrix Membranes Modified with Amino Acid for Arsenic Removal from Water, Polym. Sci. Technol., 30, 88-1463, 2017.
  9. Tripathi A. and Ranjan M.R., Heavy Metal Removal from Wastewater Using Low Cost Adsorbents, Bioremed. Biodeg., 6, 315, 2015.
  10. Chandra V., Park J., Chun Y., Lee J., Hwang I.-C., and Kim K.S., Water-Dispersible Magnetite-Reduced Graphene Oxide Composites for Arsenic Removal, ACS Nano, 4, 3979-3986, 2010.
  11. Kanel S.R., Manning B., Charlet L., and Choi H., Removal of Arsenic(III) from Groundwater by Nanoscale Zero-Valent Iron, Sci. Technol., 39, 1291-1298, 2005.
  12. Chen W., Parette R., Zou J., Cannon F.S., and Dempsey B.A., Arsenic Removal by Iron-Modified Activated Carbon, Water Res., 41, 1851-1858, 2007.
  13. Liu R., Zhu L., He Z., Lan H., Liu H., and Qu J., Simultaneous Removal of Arsenic and Fluoride by Freshly-Prepared Aluminum hydroxide, Colloids Surf. A: Physicochem. Eng. Asp., 466, 147-153, 2015.
  14. Lin T.F. and Wu J.K., Adsorption of Arsenite and Arsenate within Activated Alumina Grains: Equilibrium and Kinetics, Water Res., 35, 2049-2057, 2001.
  15. Chutia P., Kato S., Kojima T., and Satokawa S., Arsenic Adsorption from Aqueous Solution on Synthetic Zeolites, Hazard. Mater., 162, 440-447, 2009.
  16. Baskan M.B. and Pala A., Removal of Arsenic from Drinking Water Using Modified Natural Zeolite, Desalination, 281, 396-403, 2011.
  17. Mohan D. and Pittman C.U. (Jr), Arsenic Removal from Water/Wastewater Using Adsorbents-A Critical Review, Hazard., Mater., 142, 1-53, 2007.
  18. Ruggieri F., Marín V., Gimeno D., Fernandez-Turiel J., García-Valles M., and Gutierrez L., Application of Zeolitic Volcanic Rocks for Arsenic Removal from Water, Geology, 101, 245-250, 2008.
  19. Thirunavukkarasu O., Viraraghavan T., and Subramanian K.S., Arsenic Removal from Drinking Water Using Iron Oxide-Coated Sand, Water Air Soil Pollut., 142, 95-111, 2003.
  20. Yin H., Kong M., Gu X., and Chen H., Removal of Arsenic from Water by Porous Charred Granulated Attapulgite-Supported Hydrated Iron oxide in Bath and Column Modes, Clean. Product., 166, 88-97, 2017.
  21. Liu J.F., Zhao Z.S., and Jiang G., Coating Fe3O4 Magnetic Nanoparticles with Humic Acid for High Efficient Removal of Heavy Metals in Water, Sci. Technol., 42, 6949-6954, 2008.
  22. Pawar R.R., Hong S.M., Jin K.J., and Lee S.M., Iron-Oxide Modified Sericite Alginate Beads: A Sustainable Adsorbent for the Removal of As(V) and Pb(II) from Aqueous Solutions, Molecul. Liquids, 240, 497-503, 2017.
  23. Lata S. and Samadder S., Removal of Arsenic from Water Using Nano Adsorbents and Challenges: A Review, Environm. Manage., 166, 387-406, 2016.
  24. Lee C., Jung J., Pawar R.R., Kim M., and Lee S.-M., Arsenate and Phosphate Removal from Water Using Fe-Sericite Composite Beads in Batch and Fixed-bed Systems, Indust. Eng. Chem., 47, 375-383, 2017.
  25. Noori M., Tahmasebpoor M., and Khazini L., Effective Parameters on the Formation of Natural Zeolite-Based Granules to Remove Cationic Dyes from Contaminated Water, Polym. Sci. Technol., 34, 267-279, 2021.
  26. Mandal B. and Ray S.K., Swelling, Diffusion, Network Parameters and Adsorption Properties of IPN Hydrogel of Chitosan and Acrylic Copolymer, Sci. Eng., 44, 132-143, 2014.
  27. Yang R., Li H., Huang M., Yang H., and Li A., A Review on Chitosan-Based Flocculants and Their Applications in Water Treatment, Water Res., 95, 59-89, 2016.
  28. Tahmasebpoor M., Hosseini Nami S., Khatamian M., and Sanaei L., Arsenate Removal from Contaminated Water Using Fe2O3-Clinoptilolite Powder and Granule, Technol., 43, 116-130, 2022.
  29. Cho D.W., Jeon B.H., Jeong Y., Nam I.H., Choi U.K., Kumar R., and Song H., Synthesis of Hydrous Zirconium Oxide-Impregnated Chitosan Beads and Their Application for Removal of Fluoride and Lead, Surface Sci., 372, 13-19, 2016.
  30. Wang J., Xu W., Chen L., Huang X., and Liu J., Preparation and Evaluation of Magnetic Nanoparticles Impregnated Chitosan Beads for Arsenic Removal from Water, Eng. J., 251, 25-34, 2014.
  31. Negm N.A., Abd El Wahed M.G., Hassan A.R.A., and Abou Kana M.T.H., Feasibility of Metal Adsorption Using Brown Algae and Fungi: Effect of Biosorbents Structure on Adsorption Isotherm and Kinetics, Mol., Liq., 264, 292-305, 2018.
  32. Khatamian M., Khodakarampoor N., and Saket-Oskoui M., Efficient Removal of Arsenic Using Graphene-Zeolite Based Composites, Colloid Interface Sci., 498, 433-441, 2017.
  33. Heredia A., Gómez Avila J., Vinuesa A., Saux C., Mendoza S.M., Garay F., and Crivello M., Compared Arsenic Removal from Aqueous Solutions by Synthetic Mixed Oxides and Modified Natural Zeolites, Adsorption, 25, 1425-1436, 2019.
  34. Meher A., Pillewan P., Rayalu S., and Bansiwal A., Arsenic Removal from Water Using Metal and Metal Oxide Modified Zeolites, Arsen Res. Glob Sustain, 482-483, 2016.
  35. Du Q., Guo Y., Wu P., and Liu H., Synthesis of Hierarchically Porous TS-1 Zeolite with Excellent Deep Desulfurization Performance under Mild Conditions, Mesopor. Mater., 264, 272-280, 2018.

 

مجله علوم و تکنولوژی پلیمر
دوره 35، شماره 4 - شماره پیاپی 180
مهر و آبان 1401
صفحه 367-379

فایل ها

ارجاعات به این مقاله

هم رسانی

ارجاع به این مقاله

آمار